混流泵
混流泵是一种“拉出”式结构泵,在检查和拆卸叶轮和轴封时,毋须将与泵体相连接的管路拆开。装有精密加工的泵轴,装有稀油润滑的轴承,在填料函盖中装有防护轴套。轴承箱的油位,可由恒位油杯来控制。
泵体的支脚,可承受来自管路的任何载荷,并直接传递给基础。这样,转子不会因为泵承受泵受载荷而产生弯曲,从而保证轴承的使用寿命。
由于较大的过流面积,从而减少阻塞。
泵的旋转方向,从驱动端看,为顺时针方向。
动力驱动可采用电动机或内燃机。
泵装置上可以配备完整的放气装置,有利于吸入管路的排气。
2、水泵起动后有一股水就不出水了
After starting ,
the pump only send one stream water then no water runs out
1、吸入的水中有过多气泡
2、吸水管中窝存空气
3、吸水管或连接处垫料不严密有进气现象
4、底阀或叶轮有水草杂物填塞
1.There are too many bubbles in the
indrawn water
2.There is air in the suction pipes
3.The paddings in connected parts are
imprecision and produces leaking phenomenon
4.There are waterweeds and sundries
filled in the bottom valve or impeller
1、检查进水管末端是否在水平面以下一米左右
2、排除空气
3、高速垫料,填塞缝隙拧紧螺栓
4、消除水草杂物
1.Check the end
of water inlet pipe if it is under the water surface at one meter
2. Remove the
air
3.Add padding to
fill the gaps and then tighten the bolts
4.Clear the
waterweeds and sundries.
6、轴承发热
The bearing is
hot
1、润滑油脂不足
2、润滑油质量不好或不清洁
3、轴心没有对准
4、轴承松动或磨损
5、皮带太紧
1.Lubricating grease is not enough
2.The of lubricating oil is not
good or dirty
3.The axes is not aiming
4.The bearing is loose or attrition
5.The belt is too tight.
1、加油
2、清洗轴承
3、找正
4、修正
5、适当放松
1.Add lubrication oil
2.Wash
the bearing
3.Aligning
4.Amending
5.Loosen it properly
- 界首排污混流泵维修多重优惠 2020-07-16
- 淮北排污混流泵采购价推荐厂家 2020-07-15
- 淮北大流量轴流泵维修推荐货源 2020-07-15
- 桐城500ZLB0.6 6.3轴流泵销售价可量尺定做 泰安金石泵业公司 2020-07-15
- 铜陵350HW 10混流泵价格服务为先 2020-07-15
- 泉州市雨水混流泵价格近期行情,泰安金石泵业 2020-07-14
- 南平市900ZLB 100轴流泵厂家价格合理「多图」 2020-07-14
- 350HW 8混流泵订购价质量材质上乘 金石泵业公司 2020-07-11
- 天长农业混流泵价格承诺守信「在线咨询」 2020-07-10
- 700ZLB1.3 7.2轴流泵安装产品介绍 金石泵业公司 2020-07-09